Professional Installation
Expert engine, transmission, and drivetrain installation for boats, yachts, and commercial vessels. Precision fitment, proper alignment, and full commissioning — done right the first time.
Installation Services
Complete fitment and commissioning for engines, transmissions, and control systems.
Engine Installation
Complete removal and replacement of inboard, stern-drive, and V-drive engines. Includes alignment, coupling, and all peripheral connections.
- Old engine removal & disposal
- New engine placement & bed fitting
- Shaft alignment (within 0.003")
- Flexible coupling installation
- Exhaust system connection
- Cooling system plumbing
- Fuel line & filter installation
Transmission & Sterndrive
Precision installation of marine transmissions, sterndrives, outdrives, and IPS pods. Proper gear engagement and hydraulic connection.
- Transmission alignment & bolting
- Sterndrive / outdrive mounting
- IPS pod calibration & setup
- Shift cable adjustment
- Hydraulic line connection & bleed
- Propeller fitment & torque
- Trim tab installation
Control Systems
Throttle, shift, steering, and electronic control integration for single and multi-engine setups.
- Throttle & shift cable routing
- Electronic control unit (ECU) pairing
- Steering system connection
- Joystick & autopilot integration
- Instrument panel wiring
- Trim & tab switch installation
- SeaStar / Uflex system setup
Electrical & Electronics
Complete engine electrical integration including starters, alternators, sensors, and vessel monitoring.
- Battery & charging system setup
- Starter & alternator wiring
- Engine sensor harness routing
- CAN bus / NMEA 2000 integration
- Vessel monitoring display setup
- Bilge pump & alarm wiring
- Grounding & bonding verification
Exhaust & Cooling
Proper exhaust and cooling system installation to prevent overheating, corrosion, and noise issues.
- Wet exhaust manifold connection
- Riser & elbow installation
- Raw water pump & plumbing
- Heat exchanger connection
- Closed cooling system fill & bleed
- Exhaust hose & waterlift muffler
- Thru-hull & seacock verification
Commissioning & Sea Trial
Post-installation testing and calibration to verify everything works perfectly before handover.
- Initial startup & leak inspection
- Idle & RPM range verification
- Alignment recheck under load
- Cooling system temperature check
- Sea trial with data logging
- Trim & handling optimization
- Owner walkthrough & handover
Warranty & Professional Installation
Why proper installation matters for your engine warranty and long-term reliability.
Professional Installation Required for Warranty
All crate engines, remanufactured engines, and transmissions sold by Marine Engine Service carry a 12-24 month warranty — but coverage is contingent on professional installation by a qualified marine technician.
What qualifies as "professional installation"?
- Performed by a certified marine technician or authorized dealer
- Shaft alignment checked with dial indicator (within 0.003" TIR)
- All fluids filled to manufacturer specification
- Cooling system bled and verified for flow
- Electrical connections properly crimped, sealed, and grounded
- Proper break-in procedure followed and documented
- Installation receipt retained for warranty claims
When you choose Marine Engine Service for installation, you receive a complete installation certificate that satisfies all warranty requirements and protects your investment.
Our Installation Process
A systematic approach that ensures every installation is safe, precise, and warranty-compliant.
Survey
We inspect your vessel, measure clearances, and plan the installation before any work begins.
Removal
Safe removal of the old engine, transmission, and associated components. Proper disposal arranged.
Prep
Engine beds inspected and reinforced if needed. New mounts, hardware, and gaskets prepared.
Install
Engine lowered into place, aligned, coupled, and all systems connected to manufacturer spec.
Test
Dockside run, then sea trial. All systems verified. Data logged. Installation certificate issued.
Why Choose Our Installation Service?
Precision, accountability, and peace of mind — from haul-out to handover.
Certified Installers
Factory-trained on Mercury, Yamaha, Volvo Penta, Cummins, and Caterpillar installation procedures.
Precision Alignment
Dial-indicator shaft alignment within 0.003" TIR — critical for bearing and coupling longevity.
Warranty Certificate
Every installation includes a documented certificate required for engine and transmission warranty claims.
Fixed Pricing
Detailed estimate before work starts. No surprises, no hidden fees, no scope creep.
Full Documentation
Photos, measurements, torque specs, and a complete installation report provided on handover.
Sea Trial Included
Every installation includes a sea trial to verify performance, cooling, and handling under real conditions.
Book Your Professional Installation
Protect your warranty and ensure peak performance. Contact us to schedule a vessel survey and installation estimate.
Request Installation QuoteOr call +48 123 456 789 — Monday to Friday, 08:00 – 17:00 CET
